亚洲人成中文字幕在线观看,国产精品久久毛片,播放灌醉水嫩大学生国内精品,欧美性猛交xxxx乱大交



Common problems of drying and curing in coating production line
Time:2012-10-22 11:52:48

       Drying and curing equipment is mainly composed of drying chamber, heating system and temperature control. The drying chamber body has through type, through type; Heating system heating mode is fuel (heavy oil, light oil), gas (natural gas, liquefied gas), electric heating (far infrared, electric heating), steam, and so on.


       Drying and curing equipment relatively few problems, but in the heat preservation and energy saving and safety aspects should still cause attention.


       The external surface temperature of drying chamber is too high

       Improper selection of thermal insulation materials is the main reason for poor thermal insulation effect, excessive surface temperature and unsatisfactory thermal insulation performance. This not only increases energy consumption, but also fails to meet the requirements of Article 5.9.2 in the National standard GB1444321993 "Safety Regulations for Coating Operation" : the drying room should have good insulation, and the surface temperature of the outer wall should not be higher than room temperature 15℃.


2. The exhaust pipe is improperly set or not set

       The exhaust pipe of the drying and curing room of some coating lines is not connected to the outside, but in the workshop, the waste gas is directly discharged into the workshop, causing air pollution in the workshop; The exhaust outlet of the drying and curing chamber of some coating lines is not set in the position with the highest concentration of exhaust gas, which is not conducive to the rapid discharge of exhaust gas and the prevention of accumulation. It also does not meet the requirements of national standard GB1444321993 article 5.1.6: The exhaust outlet of the drying room should be set in the area with the highest concentration of combustible gas. After spraying the workpiece into the drying and curing room, because the paint contains organic solvents to varying degrees, the drying and curing process will produce organic solvent waste gas, organic solvent waste gas has flammability, if the waste gas is not discharged from the drying room in time and accumulated in the drying room, once the concentration is too high will cause safety hazards.

Service hotline

020-36860788

WeChat

Feedback

Feedback

被夫の上司に犯中文字幕| 日本三级片在线观看| 欧美老妇交乱视频在线观看| 三级全黄不卡的| www.色五月| 国产在线一区二区三区四区五区| 成人免费a级毛片天天看| 亚洲午夜私人影院在线观看| 久久精品无码精品免费专区| 女人扒开腿让男人狂桶30分钟| 色婷婷六月亚洲婷婷国产| 亚洲av永久中文无码精品综合| 黄 色 成 人 免费网站| 午夜射精日本三级| 美女隐私无遮挡免费视频软件| 国产精品边做奶水狂喷| 欧美怡红院免费全部视频 | 亚洲夜夜欢a∨一区二区三区| 中国china露脸自拍性hd| 无码国产精品一区二区免费式| 人妻夜夜爽天天爽三区| 97SE亚洲国产综合在线| 日本免费a级毛一片| 99久久国语露脸精品国产色| 国精产品推荐视频| 成人免费精品网站在线观看影片| 久久人搡人人玩人妻精品首页| 亚洲AV中文AⅤ无码AV接吻| 日本日本乱码伦视频免费| 日韩黄色网站| 日韩一区二区三区无码A片| 欧美成人性生免费看的| 欧美大bbbb流白水| 新版天堂资源中文8在线| 国产日韩一区二区三免费高清| 国产一区二区三区日韩精品| 最近中文字幕完整视频| 久久亚洲粉嫩高潮的18P| 浪荡艳妇爆乳jufd汗だく肉感| 免费A级毛片免费观看视频| 无码专区—va亚洲v天堂|